Misc. Plumbing

Blow Out Plug

  • Apply air pressure to your water lines
  • Will hold air pressure until removed
  • Releases pressure by opening a faucet (do not depress the check valve on your water fill)

Part Number:
03054 - Blow Out Plug, pkg.

Dual Barbed Drain Cock

  • Fits most OEM fresh water drain valves as well as those mounted on the exterior walls
  • Fits: 3/8” - 1/2” barbs

Part Number:
03182 - White, pkg.

Dual Threaded Drain Cock

  • Fits most OEM fresh water drain valves as well as those mounted on the exterior walls
  • Fits: 3/8” - 1/2” MPT

Part Number:
03175 - White, pkg.

Exterior Evacuation Drain Port

  • For use when draining a sink or shower directly to the exterior of the unit using a bucket or portable holding tank
  • Connected using a 3/4” vinyl or plastic tubing
  • Exterior connection uses a standard water hose
  • Outside Dim: 1-1/2" dia.

Part Number:
95185 - White, pkg.

Exterior Evacuation Drain Trap

  • For use when draining a sink or shower directly to the exterior of the unit using a bucket or portable holding tank
  • Standard 3/4” MPT water hose connection
  • 1-3/4” standard strainer connection

Part Number:
95195 - White, pkg.

Flush Slip Fitting

  • Will bond directly to the surface of the tank
  • Constructed of ABS plastic

Part Number:
221 - 1-1/2” Black, bulk

Flush Slip Fitting

  • Will bond directly to the surface of the tank
  • Constructed of ABS plastic

Part Number:
217 - 2” Black, bulk

Flush Threaded Fitting

  • Will bond directly to the surface of the tank
  • Constructed of ABS plastic

Part Number:
220-B-76 - 3” Black, bulk

Holding Tank Heater

  • Used on either fresh water or septic tank
  • Dual voltage ready for 12V and 110V applications
  • Thermostatically controlled and active at 34° F
  • Foil covered heater is 30” x 13” with 24” ground wire
  • Draws approximately 1 Amp AC and 10 Amps DC current when in use
  • Multiple heaters may be used where needed for tank coverage

Part Number:
HTH-A - Holding Tank Heater, pkg.

Holding Tank Sprayer

  • Creates a high pressure, multi-directional spray to help clean tank
  • IAPMO and Canadian certified
  • Must be installed no lower than 2" from the top of the tank to meet IAPMO and Canadian certification

Part Number:
571-Sprayer-A - Sprayer, pkg.

Manual Water Faucet

  • Self-priming and provides constant water flow
  • Requires 1-3/4” access hole
  • Plumbing hook-up is not provided but uses a threaded 1/4” MPT fitting
  • Instructions included

Part Number:
97025 - Manual Water Faucet, pkg.

Projected Male Spigot

  • Has small protrusion that will fit into the hole in the tank
  • Constructed of ABS plastic

Part Number:
216-A-MS-A - 3” Black, pkg.

Projected Slip Fitting

  • Will bond directly to the surface of the tank
  • Constructed of ABS plastic

Part Number:
216-SF - 3” Black, bulk

Vacuum Breaker/Check Valve

  • Installed between water inlet connection and tank flusher
  • Prevents harmful bacteria and waste from entering the hose or water supply system
  • Meets IAPMO standards
  • ASSE 1001-02 requires installation of 6" or more above the highest point of any item connected to the waste tank where the flusher is being installed

Part Number:
571-Vac-Chk-A - Black, pkg.

Water Inlet

  • Reduces corrosion associated with tank flusher operations
  • Does not have a backflow breaker for better water movement
  • Plastic check valve body

Part Number:
160-85-A-2PZ-A - White, pkg.